HENAN RECYCLE ENVIRONMENTAL PROTECTION EQUIPMENT CO., LTD.
Mills
Zhengzhou, Henan
Member since : 21/12/2023
Copper Cable Stripping Machine: Sell Offer
Expired Offer
![`Recycleinme Hot Offer for ${props.userfulldetails[0].CompanyName}`](/images/hot-offer.png "`Recycleinme Hot Offer for ${props.userfulldetails[0].CompanyName}`")
Hot OfferUnit : Number
PCK : Containers
QTY : 100
Details:
The newly introduced multifunctional wire stripping machine is engineered to process wires ranging from 1mm to 200mm in diameter. Designed for both manual and electric operation, it efficiently removes the outer sheath and inner conductor of scrap cables. With its dual-mode functionality, users can switch between precise manual control and high-efficiency automated stripping using the intelligent electric mode.
In terms of working and using this machine, there are mainly the following points worth noting:
When the machine is working, special attention should be paid to the safety of both hands. When processing sheath lines and cross-head operations, the operator must concentrate and a safety cover must be installed in the middle.
When processing sheathed wires and various cables, the pressure should not be too tight, and the operation should not be overloaded to avoid affecting the service life of each part. If the material feeding cannot be transmitted, check whether the belt is loose, whether the pressure is too tight, or whether the position of the knife is in the wrong direction.
If this machine works under heavy load for a long time, the oil reserve of the transmission should be checked every quarter, and the four teeth of the transmission shaft should be lubricated with butter every shift.
The four Z208 bearings of the upper and lower spindles should be checked regularly to see if the bearings and shafts are running smoothly and whether the bearings are damaged. If this occurs, they should be repaired in time. Otherwise, if used continuously, the shaft will easily break.
When the upper shaft needs to be lifted for work, the heights of both sides should be relatively parallel.
The four lifting screws of the transmission and the four lifting screws of the motor should be adjusted regularly one by one to check whether there is any looseness. If so, the chain and V-belt should be adjusted and tightened in time. When adjusting, the transmission or motor must be relatively parallel and not too tilted.
In terms of working and using this machine, there are mainly the following points worth noting:
When the machine is working, special attention should be paid to the safety of both hands. When processing sheath lines and cross-head operations, the operator must concentrate and a safety cover must be installed in the middle.
When processing sheathed wires and various cables, the pressure should not be too tight, and the operation should not be overloaded to avoid affecting the service life of each part. If the material feeding cannot be transmitted, check whether the belt is loose, whether the pressure is too tight, or whether the position of the knife is in the wrong direction.
If this machine works under heavy load for a long time, the oil reserve of the transmission should be checked every quarter, and the four teeth of the transmission shaft should be lubricated with butter every shift.
The four Z208 bearings of the upper and lower spindles should be checked regularly to see if the bearings and shafts are running smoothly and whether the bearings are damaged. If this occurs, they should be repaired in time. Otherwise, if used continuously, the shaft will easily break.
When the upper shaft needs to be lifted for work, the heights of both sides should be relatively parallel.
The four lifting screws of the transmission and the four lifting screws of the motor should be adjusted regularly one by one to check whether there is any looseness. If so, the chain and V-belt should be adjusted and tightened in time. When adjusting, the transmission or motor must be relatively parallel and not too tilted.
Contact Details
Sell Offers
...more
Similar Sell Offers
Nawab Iron & Steel Re-Rolling Mills, established in 2009 and based in Kota, Indi ...>>
Tc-Montagem Industrial Ltd, a trusted scrap trading company based in Santo Ângel ...>>
We, Evaaya Trading Company, are offering Copper Ore sourced directly from Canada ...>>
The newly launched multifunctional wire stripping machine is expertly designed t ...>>
CM Trading Co., Ltd., a reputable scrap trading company based in Daegu, South Ko ...>>
DE RECYCLING, a recycling company based in Seychelles, has 10 metric tons of Cop ...>>
Oasis Imports & Exports Ltd, based in Auckland, New Zealand, is currently seekin ...>>
Star Mediterranea, a dynamic and customer-oriented scrap trading company based i ...>>
Lucky April Metal Corp Offering Copper Wire Scrap with 20 MT available for expor ...>>
Surya Batam Cemerlang Supplying Copper Tinplate Scrap from Indonesia with 100 MT ...>>
Surya Batam Cemerlang Selling Copper Millberry Scrap for buyers seeking copper s ...>>
Uoi Gold Diamond Africa Sarl, established in 2016 and based in Kinshasa, Congo, ...>>
Can't find what you are looking for? Become a RIM member now and post your requirement
HENAN RECYCLE ENVIRONMENTAL PROTECTION EQUIPMENT CO., LTD.
Mills
Zhengzhou, Henan
Member since: 21/12/2023Copper Cable Stripping Machine: Sell Offer
Expired Offer
Hot OfferUnit : Number
PCK : Containers
QTY : 100
Details:
The newly introduced multifunctional wire stripping machine is engineered to process wires ranging from 1mm to 200mm in diameter. Designed for both manual and electric operation, it efficiently removes the outer sheath and inner conductor of scrap cables. With its dual-mode functionality, users can switch between precise manual control and high-efficiency automated stripping using the intelligent electric mode.
In terms of working and using this machine, there are mainly the following points worth noting:
When the machine is working, special attention should be paid to the safety of both hands. When processing sheath lines and cross-head operations, the operator must concentrate and a safety cover must be installed in the middle.
When processing sheathed wires and various cables, the pressure should not be too tight, and the operation should not be overloaded to avoid affecting the service life of each part. If the material feeding cannot be transmitted, check whether the belt is loose, whether the pressure is too tight, or whether the position of the knife is in the wrong direction.
If this machine works under heavy load for a long time, the oil reserve of the transmission should be checked every quarter, and the four teeth of the transmission shaft should be lubricated with butter every shift.
The four Z208 bearings of the upper and lower spindles should be checked regularly to see if the bearings and shafts are running smoothly and whether the bearings are damaged. If this occurs, they should be repaired in time. Otherwise, if used continuously, the shaft will easily break.
When the upper shaft needs to be lifted for work, the heights of both sides should be relatively parallel.
The four lifting screws of the transmission and the four lifting screws of the motor should be adjusted regularly one by one to check whether there is any looseness. If so, the chain and V-belt should be adjusted and tightened in time. When adjusting, the transmission or motor must be relatively parallel and not too tilted.
In terms of working and using this machine, there are mainly the following points worth noting:
When the machine is working, special attention should be paid to the safety of both hands. When processing sheath lines and cross-head operations, the operator must concentrate and a safety cover must be installed in the middle.
When processing sheathed wires and various cables, the pressure should not be too tight, and the operation should not be overloaded to avoid affecting the service life of each part. If the material feeding cannot be transmitted, check whether the belt is loose, whether the pressure is too tight, or whether the position of the knife is in the wrong direction.
If this machine works under heavy load for a long time, the oil reserve of the transmission should be checked every quarter, and the four teeth of the transmission shaft should be lubricated with butter every shift.
The four Z208 bearings of the upper and lower spindles should be checked regularly to see if the bearings and shafts are running smoothly and whether the bearings are damaged. If this occurs, they should be repaired in time. Otherwise, if used continuously, the shaft will easily break.
When the upper shaft needs to be lifted for work, the heights of both sides should be relatively parallel.
The four lifting screws of the transmission and the four lifting screws of the motor should be adjusted regularly one by one to check whether there is any looseness. If so, the chain and V-belt should be adjusted and tightened in time. When adjusting, the transmission or motor must be relatively parallel and not too tilted.
Contact Details
Name: Mrs.Lisa
Company: HENAN RECYCLE ENVIRONMENTAL PROTECTION EQUIPMENT C
City: Zhengzhou
State: Henan
Country: China
ChinaAddress: Henan Communication Industrial Park) 5th St., Economic-Technological Development Zone,
ZipCode: 450000
Phone view details
Mobile view details
Email view details
Website view details
Sell Offers
...moreSimilar Sell Offers
Nawab Iron & Steel Re-Rolling Mills, established in 2009 and based in Kota, Indi ...>>
Tc-Montagem Industrial Ltd, a trusted scrap trading company based in Santo Ângel ...>>
We, Evaaya Trading Company, are offering Copper Ore sourced directly from Canada ...>>
The newly launched multifunctional wire stripping machine is expertly designed t ...>>
CM Trading Co., Ltd., a reputable scrap trading company based in Daegu, South Ko ...>>
DE RECYCLING, a recycling company based in Seychelles, has 10 metric tons of Cop ...>>
Oasis Imports & Exports Ltd, based in Auckland, New Zealand, is currently seekin ...>>
Star Mediterranea, a dynamic and customer-oriented scrap trading company based i ...>>
Lucky April Metal Corp Offering Copper Wire Scrap with 20 MT available for expor ...>>
Surya Batam Cemerlang Supplying Copper Tinplate Scrap from Indonesia with 100 MT ...>>
Surya Batam Cemerlang Selling Copper Millberry Scrap for buyers seeking copper s ...>>
Uoi Gold Diamond Africa Sarl, established in 2016 and based in Kinshasa, Congo, ...>>
Can't find what you are looking for? Become a RIM member now and post your requirement
Business at RIM
Browse Scrap Sell OffersRIM Scrap Prices
Free Scrap PricesSupport & Contact
© 2003-2026 - Whitelake B2B Pvt Ltd. All Rights Reserved
Business at RIM
Support & Contact
© 2003-2026 - Whitelake B2B Pvt Ltd. All Rights Reserved